Info Foto's  
  AAF9 Signaalmeter 1 MHz to 14 GHz  
       
       
r Fixed internal antennas requiring no adjusting.
r High sensitivity, -90 dBm @ 2.4 GHz, -80 dBm @ 5.8 GHz, -60 dBM @ 12 GHz.
r A 1 MHz to 14 GHz bandwidth.
r A switched external Coaxial SMA connector for directional antennas, or frequency filters
r A high-frequency band pass filtering system-eliminating noise in the lower frequencies that conceal higher frequency signals
r A USB output for remote monitoring, and powering. The remote signal can also be used to switch on & off security accessories (DVRs, cameras, alarms)
r Differentiation between Digital and Analog signals
r Audio ouputs for AM detection and hearing signal strength levels with a VCO
r A directional 1.8-6.4 GHz Log Periodic antenna
r Omni directional 0.9, 1.2, 2.4, and 5.8 GHz dipole antennas
r Volume controlled headphones, speaker, USB cable, SMA/BNC coaxial adapter, and 100 to 240 VAC international power supply
r A hard, crush-resistant carrying case.

The AAF9 is a professional Radio Frequency (RF) measuring instrument. It excels at detecting and measuring all Radio Frequency signals between 1 MHz to 14 GHz. The AAF9 has the latest micro-IC components, pre-amplifiers, high frequencies filters and advanced circuiting that are by products of the wireless boon in electronics. It employs several stages of active detection (rather than a diode detector) giving it extraordinary sensitivity. The sensitivity of this instrument approaches that of a tuned receiver. Even with this high sensitivity, it still has broadband detection capabilities that enable it to measure all signals – irrespective of being spread–spectrum, frequency hopping, pulsing or trunking. High sensitivity is needed to detect the weak signals from covert milliwatt transmitters, cell phones and tiny hidden cameras. The newer 5.8 GHz and 2.4 GHz transmitting devices can be detected at greater than 10-20 feet (~3-6 meters) using the AAF9. This allows the quick and effective security sweeps of large conference rooms or small restrooms. Signal overload is avoided by using a logarithmic amplifier with 1000 to 1 dynamic signal range – making it easy to pinpoint the signal source at its exact location.

       
Specificaties
       
Sensitivity: -90 dBm at 2.4 GHz, -80 dBm at 5.8 GHz, -60 dBm at 12 GHz
Bandwidth: < 1 MHz to > 14 GHz. Simultaneous multiband detecting including spread spectrum, signal hopping and trunking
Sensitivity Controller: 20 dB, (10 to 1) signal range adjustment
Detection Modes: LINEAR - far-field detection of the weakest signals, 15 dB dynamic range
  LOG - near-field localization and pinpointing, 60 dB dynamic range
  MID - intermediate detection, 30 dB dynamic signal range
Antenna Selection: INT - internal, fixed, omnidirectional broadband antennas. No adjustments required with telescopic antennas.
  SMA - 50 ohms impedance, DC isolated; SMA female external coaxial connector for frequency specific and/or directional antennas, screw-on filters or attenuators.
Band Select Switch: The band select switch is used to switch between a full received band or a band of frequencies solely above 1.5 to 2 GHz. A multi-stage bandpass filter system is used to reduce signal levels below 1.5 GHz. This filters out most “noise” allowing exceptionally weak high frequency signals to be detected
Audio Outputs: VCO - Audio-frequency changing Voltage Controlled Oscillator
for hearing differences in detected signal levels by different pitch levels
AM – Enhanced AM detection; RF signal characterization and identification
Analog Mode: Detecting and measuring continuously transmitted signals
Digital Mode: peak detection, identifying and measuring digital and pulsed signals
Audio Output Jack: 1V. P-P, 45 mw, 3.5 mm audio stereo jack for earphones or speakers, 15 ohms
Analog Meter Display: Visual indication of changes and levels of RF signal strength
LED Display: Gradually dimming and enhanced LED lighting depending upon detected signal strength; for recognizing the signal strength from a distance or in darkness.
  Green LED - Maximum at low signal levels-dims as signal strength increases
  Red LED – Unlit at low signal levels – gradually changes from dim to bright as signal level gets stronger
  Simultaneous lit Green and Red LEDs due to Digital Signals with rapid on/off switching
Mini USB Connector: External meter monitoring, 0.2 to 2.7 V dc output, 1 K impedance; Can be used for CMOS switching of digital video recorders,
1 volt P-P audio output of switch selected AM or VCO audio, 15 ohms.
+ 5 VDC (100 ma.) to the connector can externally power the AAF9
Weight: 156 g. with batteries installed
Dimensions: 5.6 cm wide x 13 cm high x 3.1 cm thick
Power supply: 2 AA Alkaline batteries
Battery Life: Approximately 40 hours
Goedkeuring: CE, RoHS en WEEE
       
Leveringsomvang
       
l AAF9 Signaalmeter 1 MHz to 14 GHz
l Headphone
l Plug-in mini-speaker
l SMA to BNC coaxial adapter
l 1,8 - 6,4 GHz Log periodical antenna
l 110-240 VAC power supply
l 3 Dipole antennas (0,8 - 0,9, 1,2-2,4, 5.8 GHz)
l USB adapter cable
l Carry case
l Gebruiksaanwijzing
    Info Foto's